Name: Michelin Power All Season Tyre (28-622)
Brand: Michelin
SKU: MIC-019821
Price: 52.99 GBP
Availability: OutOfStock

Description
Specification

Experience the ultimate bike ride regardless of the season with the superb Michelin Power All Season Tyre 700 x 25c. This fantastic tyre has been engineered for maximum grip in all weather conditions. Thanks to the new Aramid Protek+ reinforcement material, this tyre offers increased puncture resistance. Plus, with the new generation of tread design and Hi-Grip Design, you'll enjoy a 15% boost in grip - increasing your safety on slippery and muddy surfaces.

Featuring a Grip Compound, this special rubber mix performs excellently even in low temperatures, bolstering your security on wet, muddy, and slippery terrains. The Hi-Grip Design further enhances grip, offering heightened safety even in particularly unfavourable conditions. Additionally, the tyre is equipped with Aramid Protek+ for extra protection. This wider protective layer in the shoulder area proves to be more resistant to cuts than traditional materials, promising longevity.

There's more - this tyre can save you time on your rides! Expect to find a gain of 5 watts per pair of tyres, which translates into 20 seconds saved over 40 km at an average speed of 45km/h.

Unleash the power of your bike with the Michelin Power All Season Tyre and enjoy resilience, performance, and safety all year round.

STANDARD TYRE FITTING
(with inner tube)

Carefully check the condition of the rim. A poor-condition, broken or cracked rim must be replaced as it could cause leaks and be dangerous.
Check the condition of the rim tape. Broken or cracked tape must be replaced as this often causes punctures.
Insert the 1st bead into the rim.
Slightly inflate the inner tube to make it round and insert it into the tyre, starting with the valve. For latex inner tubes, do not forget to apply talc to make it easier to position it in the tyre.
Repeat for the 2nd bead starting on the opposite side to the valve and positioning the bead at the bottom of the rim. Finish off fitting near to the valve.

TUBELESS READY

A Tubeless Ready tyre is a tyre that can be fitted without an inner tube. It is made airtight using sealant rather than an inner tube.

To fit a tubeless tyre:

Use a UST Tubeless wheel.
Add sealant.
Comply with the maximum pressure indicated on the tyre sidewall.

TUBELESS

Use a UST-Tubeless rim. Carefully check the condition of the rim. A poor-condition, broken or cracked rim must be replaced as it could cause leaks and be dangerous.
The rim must be lubricated all over to make it easier to move around when fitting the tyre but mainly so it can be centered perfectly.
The lubricant must be soapy water type or equivalent (no oil or grease).
Start by positioning the first bead on the opposite side to the valve, taking care to position the bead at the bottom of the well.
Inflate the tyre until it is in position without exceeding the maximum pressure indicated on the sidewalls and make sure that the tyre is properly centered. Adjust the pressure after cycling a few miles.

REMOVING

Loosen the beads from around the rim.
Push them to the bottom of the well.
Carefully position a tyre lever on either side of the valve (about 10cm) and lift the tyre over the rim hook.
Work one of the levers around the rim between the hook and bead to fully remove the first bead.
Extract 2nd bead by hand.

RIM TAPE

This protects the inner tube in contact with the rim, preventing it from being damaged by spoke ends once it is inflated. It must be the width of the rim cavity. There is a Tubeless version for Tubeless and Tubeless Ready tyres.

Colours	Black
Sizes	700 x 23C, 700 x 25C, 700 x 28C
Brand	Michelin
Model Year	2026
Barcodes	3528700198218, 3528701464046, 3528709206211
SKUs / Part Numbers	MIC-019821, MIC-146404, MIC-920621